Test Cell

Validity Proven

There are Thousand of builders now globally We invite you to invest and join in to also Support the rise of this technology.

We show h2 some example the work Carried Out Proving the Technology reebuilding it and now mass  deployment.

Do you self and Mankind A Favor Download this Page and      Re upload to new websites. and Pass to Schools.

Powered by   High Voltage, High Frequency nanopulses.

The WFC is a water capacitor and uses ORDINARY TAP WATER without any electrolyte...

Stanley A Meyer Single Test Cell Voltrol

January 25, 2013 - TESTS02E01 :

Following the TEST  about the production of HHO gas,

I have continued the tests with the Stanley Meyer's Water Fuel Cell (WFC).

 

The TEST has demonstrated that High Voltage Nano Pulses at High Frequency produced   accross an electrolysis cell are able to produce very quickly a great amount of HHO gas.

 

According to these encouraging tests, I have reconducted my experiments done about the Stanley Meyer's WFC from June 2008.

 

 I have replaced the VIC (Voltage Intensifier Circuit), a replication of the   Stanley A  Meyer's circuit,  with 100% positive results.

 

Dan

"I encourage all schools and builders to replicate and teach such technologies aggressively."

Notes : 

The use of pure osmosed water without electrolyte (not electrically conductible) is very important here, this has allowed to remove completly the HHO generation by electrolysis.

AS ZERO  SALTS ZERO ELECTROLYTES ONLY PURE OSMOSED WATER.

The WFC is a water capacitor, in this test it consumes too much current due to its impedance Vs the pulsed current.

 

During long duration tests (>6min) the WFC begins to heat up and thus, this confirms this fact. The effect discovered by Stanley Meyer seems really present here, because the pure osmosed water is split.

The High Voltage pulse sent by the induction  accross the WFC via the flat bifilar coil need to be optimized so as to reduce the current. I think that the WFC must be used as a capacitor in a resonant RLC type circuit like the Meyer's VIC original circuit..SEE  9XB  and    9XA Pages

THE PARAMETRIC POWER CONVERSION
 
Created on April 16th, 1997 - JLN Labs - Last update : January 10th, 2003
Thanks to Fred B. EppsGreg WatsonEpitaxy


All informations in this page are published free and are intended for private/educational purposes and not for commercial applications

As shown by Equation #1, electromotive force, and hence the transfer of electrical energy can be achieved in two ways:

 

(1) by flux coupling,

or

(2) by parametric coupling.

Equation #1

Figure 1 

Consider a simple inductance (L) carrying a current (i) as shown in fig 1.

One knows that there is energy stored in this inductance of magnitude 1/2 LI*2 and if this inductance is now increased in some manner, such as by inserting an iron core into L (while holding I constant). then the stored electrical energy is increased. This is an example of parametric power transfer. (see Equation 1).

Specials comments :

"NO energy is required to insert the iron core into the inductor.

 

It is ATTRACTED into the core and the resultant increased coil energy is pumped back into the power source (coil current drops)!" (Greg Watson)

"No mechanical energy input is required to insert the iron core into the inductor, BECAUSE iron core is attracted by the inductor itself, thus no mechanical energy need to be expended !" (Epitaxy)

If in accordance whith Fig 2, the afore-mentionned core is now alternately inserted into and withdrawn from the inductance L and this inductance is, in turn a part of tank circuit, then a parametric oscillator result.

Figure 2

The most critical relationship associated with this parametric oscillator relate to frequency. For such devices, it is a well known fact that ideally, the pumping frequency (rotating eccentric) should be twice the frequency to which the resonant tank is tuned ( fig 3 ).

Fig 3

The following example demonstrate the general validity of this statement :

Assume that the current in the tank is oscillating at one-half the frequency of rotating eccentric ( see fig 4 ).

Fig 4

Current in LC Tank

Referring to fig 4, if the core is inserted at point (1) in the cycle, this increase in L, coupled with the large current flowing at that time, results in a large parametric energy transfer from the mechanism to the circuit.

 

Furthermore, if the core is now withdrawn one-half of a mechanical cycle later (or one-quarter of an electrical cycle at point (2), the current is now zero and no electrical energy is withdraw from the tank. Similarly at point (3) we have additional parametric energy transfer and at (4) no transfer.

 

Thus, by doubling the pumping frequency, power can be unilaterally transferred parametrically in accordance with the second term of Equation 1.

Fig 5
Parametric amplification of energy

Fig 6
Transient state

( start of parametric amplification )

In the example cited above, a mechanical driver was used. The final step, of course, is to achieve a simple passive all-electrical parametric device in which the double frequency pumping action is an intrinsic part of the device.

( Ref document : The PARAFORMER (TM), "A new passive power conversion device" by Dr S.D.Wanlass and Dr L.K. Wanlass )

HHo Tube Cells Hydrogen
Below the details of the WFC cell used for this
"proof of concept" experiment.

Preliminary tests of the 1st WFC v1.0 ( June 12, 2008):

Below, the video of the experimental WFC v1.0 working in resonance mode with distilled water. A high flow of gases is produced at the WFC v1.0 resonance frequency.

 

You may notice that, in this case, the size of the bubbles produced are very tiny compared to a common electrolysis process.

Here is the Water Fuel Cell, the most important thing is that the WFC uses only ORDINARY TAP WATER without need of ELECTROLYTE for working properly. The stainless steel electrodes are the main parts of a water capacitor.

The High Frequency is rectified via an ultra fast HFA25PB60 diode so as to produce High Frequency DC pulses accross the WFC.

The full datasheet of the diode can be found HERE

Below the details of the WFC cell used for this "proof of concept" experiment.

Stanley A Meyer Single Test Cell Voltrol

Parametric Resonance

This demonstration illustrates parametric resonance, which is a resonance phenomenon that arises because some parameter of the system is varying periodically in time.

 

This happens, for example, when you periodically extend and retract your legs at an appropriate frequency while sitting on a playground swing. If a pendulum consists of a mass connected to a frictionless hinge by an idealized rod of length L, then the angle θ between the rod and vertical obeys the differential equation

θ" + (g/L) sinθ=0

If the length of the pendulum varies with time, the differential equation becomes

θ" + 2(L'(t)/L(t))θ'+(g/L(t)) sinθ=0

In this Applet, we choose the length of the pendulum to be L(t)=1+A cos(wt) and we choose g=4π2. With this choice of g, solutions of the A=0, linearized equation θ"+gθ=0 have period 1.

At time t, the length of the blue line in the Applet below is L(t). The angle between the blue line and vertical is θ(t). For comparison purposes, the gray pendulum provides the same data for the A=0, g=4π2, linearized equation

θ" + g θ =0

So, at time t, the length of the gray line is 1 and the angle between the gray line and vertical is a constant (determined by the initial speed that I have chosen) times sin(2πt).

The demonstration below is an applet. Google Chrome, Firefox and Microsoft Edge no longer execute applets because of security issues with NPAPI plugins. Some browsers that still play applets are Internet Explorer,

Safari and the Pale Moon browser [ windows, linuxMac ].

easy.

Parametric resonance tests of the WFC at 2*fo and at 0.5*fo :

When the frequency of the pump is set to Fpump = 2*fo = 1.110 MHz
the resonance of the WFC is fo= 0.687 Mhz

When the frequency of the pump is set to Fpump = 0.5*fo = 0.329 MHz
the resonance of the WFC is fo= 0.560 Mhz

Stanley Meyers's

Water Fuel Technology Works

Test of WFC v1.1 with an insulated Cathode

DBD Barrier

The center electrode of the WFC v1.0 has been covered with a thin adhesive plastic sheet so has to get a fully insulated cathod.

Thank You Hydrogen Hot Rodders.

So, it is now possible to get the Voltage Intensification with an electrical step charging effect.

Below the measured specs of the new insulated WFC v1.1.

SPECIAL BUILDER NOTE

There is a little error here the Cathod should be the outer tube and the liner on the inside of outter tube.

Reason is we want the larger + Surface are of the Outter Tube and the Smaller Negative surface on the centre -negative Annode

Above 

: The WFC 1.1 has been tested with 30V

squared pulses at 105 Hz.
When the voltage is switched off, the WFC acting as a water capacitor, discharges on itself.

A 246 mH coil have been connected in parallel with the WFC v1.1 at the output of the VIC circuit.

The voltage can be stepped up to 1.4 kV peak-peak at 13 kHz

Above : The WFC v1.1 is charged through a 9.89 kOhms resistor with the DC power supply. Now, the WFC v1.1 act as a true capacitor.


The calculated value from the curve ( 4.7 nF ) is nearly close to the measured value with the digital capacimeter ( 5.19 nF ).

Above : The WFC capacitor is disconnected from the DC power supply, its discharges on itself.


It is interesting to notice that the calculated value ( 196 kOhms) from the curve of the internal
resistance of the WFC v1.1 is less than the measured value with the digital multimeter ( 2.9 MOhms ).

Above : The WFC v1.1 is charged with the VIC, you see clearly the stepping charge effect.

Stanley A Meyer Water Test cell single tube

The T1 transformer is a common 220v/12v 60VA transformer used in reverse mode.

 

The use of a toroïdal transformer with a ferrite core will be better to minimize the HF losses in the core.

 

The T2 transformer uses a bifilar coils as described below :

Above : The VIC ( Voltage Intensifier Circuit ) is now working.

 

The WFC v1.1 is charged up to 1.1 KV in stepping charge.

Notes : With the design v1.1, I haven't yet got the same density of bubbles observed in the v1.0, the WFC v1.1 has been designed so as to get a true capacitor, the stepping charge effect can be observed has Stanley Meyer as described in his technical notes and his patent.

The adiabatic charge effect of this water ca

pacitor is very important because it minimizes de losses by Joules effect in the circuit during the charging process, so the energy transfert in the WFC is optimal.

I am currently building a new WFC v2, I shall soon publish all the infos and the datas, stay tuned...

Documents and references :

Method for the production of a fuel gas
No. Publication (Sec.) :US4936961
Date de publication :1990-06-26
Inventeur :MEYER STANLEY (US)  
Déposant :MEYER STANLEY (US) 

Abstract of US4936961

A method for obtaining the release of a fuel gas mixture including hydrogen and oxygen from water in which the water is processed as a dielectric medium in an electrical resonant circuit.

 TESTS02E03 : Here is a very interesting test which tends to proof the working principle of the Water Fuel Cell invented by Stanley Meyer.

 

The purpose of this test is to completly remove the electrolyse effect and keep only the parametrical elongation effect of the water molecule as writen by Stanley A Meyer in his

. The WFC is filled in this test with pure osmosed water (equivalent to distilled water).

 

So, the water used is not electrically conductive and can be compared to a dielectric. If, in this case, the HHO gas is produced, this can only be done with the Stanley Meyer's principle : by using the cracking of the water molecule produced by the parametrical elongation of the hydrogen-oxygen covalent bound The electrical characteristics of the Water Fuel Cell filled with a pure osmosed water are measured with a digital multimeter.

 In this test, the DC pulsed voltage and the current are measured accross the input of the WFC, just after the fast switching diode HFA25PB60.

 

The voltage accross the WFC is measured with the scope proble Ch1 (X10) and the current is computed by measuring the voltage accross a 0.1 Ohm non inductive metal resistor 10W Mundorf MR10 via the scope probe Ch2 (X10). The sampling rate of the digital oscilloscope is set to 100 MSa/sec.

 

The measurements datas are sent to a PC and then computed on Octave (an Opensource of MatLab) with the power_calc v1.02 software.

The electrical characteristics of the Water Fuel Cell filled with a pure osmosed water are measured with a digital multimeter.

Stanley A Meyer Distilled Water

Measure your cells all of them for capacitence and understand them 

Stanley A Meyer Single Test Cell Voltrol

Example of recording 6 cell assembly capcitence

Stanley A Meyer Circuit 9XB 8xa Choke Water Fuel
Stanley A Meyer Water Fuel Cell Voltrolysis Wet

Parts for making the STANLEY A MEYER 8XA/9XB Circuit 
this is a part list for the boards that we salevvminor changes from the originalv.less expensive and easier to find componates 

9XB parts list 

  • bridged rectifier, not sure of the number

       (only needed if you will use a transformer of 7 to 36 volts.)

        Use a 12 volt or 9 volt battery other wise 

  • KBU808G bridged rectifier 

  • 3 x 1000uf caps 

  • 7805 regulator 

  • .1 uf cap 

  • 330 uf cap 

  • .01 uf cap 

  • 10nf 

  • 1k , 10m. 4.7k X2 parts, 220R x 3 parts... resisters 1/4 w 

  • 4 position dip switch 

  • H11D1 opto 

  • 555 timer chip 

  • 3 x 74LS90N decade counter 

  • 7404 invert chip 

  • red Led 

  • 1 100k pot 

 

SCR  (SWITCH) part list 

  • KBU808G bridged rectifier 

  • 100 ohm resistor (20 watt or so) 

  • S4025L 

       (or simular use a heat sink and make sure the pin out matches) 

  • 1N4007 diode 

  • 6 Amp 1000 volt diode 

  • H11D2 and 220 resistor

       ( not needed if using the 9xa or the 9xb) 

NOTES FROM MILLER 

0 v limit....
If 12 volt supplied to a regulator chip.... 2 volts is lost in the chip.
The 9xd has a 12 volt and 5 volt regulator.
12 volt regulator needs 14 volt or more to output 12 volt.
A car runs on 14.5 volts. 
At rest the battery is 12 volts. So a 12 volt regulator outputs 10 volts.
A 2 volt drop through the regulator

===========================
he's taking about typical voltage regulator. 
Don't get confused about low drop out voltage 
regulators which don't have 2 v drop but they
also can't handle as much flow/current
===========
Lm317 is an adjustable regulater. 1.5 amp. 1.2 volts to 34 volts or so.
Has a 2 volt drop.
Other regulators would be buck or boost converters

7810 is a 10volt reg
Lm317 is and adjustable reg. You can make 
it a fixed voltage reg. A switch to a resistor.... 
Say 3 different resistors... 
This would output 3 different voltages. 
Preselected with the switch

One lm317 or 78xx series chips are 1.5 amps. 
Simply wire in parallel.... 2 chips are 3 amps...
 Same voltage outputs

An opamp....
Basically a voltage follower. 
There are different things they can do.
Mostly used as voltage followers..... Or amplifiers.
With a center tapped power supply.... 
They output a AC wave. Say a microphone amplifier.
With just Dc input... It will out put a DC wave.

These are simple answers. Not trying to get complex 

You also have neg voltage regulators.
Compliments to the 78xx and lm317 packages.
You need center tapped transformers for that.
Again.... This is a simplified answer.

You also. Need to pay attention to the ground icon.
For example.... Earth ground...... Chassis ground...
Ground reference...

The WFC BOOSTER (Stanley Meyer's Water Fuel Cell)
The saison 2 of the project GEGENE (Great Efficiency GENErator)...
created on december 28, 2012 - JLN Labs - last update february 7, 2013


All informations and diagrams are published freely (freeware) 
Toutes les informations et schémas sont publiés gratuitement ( freeware ) 

Cliquez ici pour la version FRANCAISE 

This is the following of the GEGENE project which uses the interesting characteristicss of a falt bifilar Tesla coil with an induction cooker as a High Frequency and High Power generator. TThe main specification of the GEGENE (Great Efficiency GENErator) is that it uses a BIFILAR PANCAKE COIL patented by Nikolas TESLA in 1894 in the patent N° 512,340. In the GEGENE the flat bifilar coil is electromagnetically coupled with the main flat coil of the induction cooker and acts as the secundary coil for the output.

 

The driving and the controlling are fully done by the main electronic controller of the induction cooker itself. So, no special electronic equipment or laboratory measurement tools are required here to succeed in this experiment. You need only : an induction cooker (for less than 50€), a dual flexible wire (speaker wire or grid wire) and some electrical connectors and plugs...

Introducing the WFC Booster project

The main purpose of the WFC Booster is trying to generate efficiently, and with a great amount, a HHO gaz (a stoechiometric mixture) which can be used as an alternative fuel.

 

The process used here is based on the WFC (Water Fuel Cell) invented by Stanley Meyer in 1990 and which consist to broke the water molecule by a parametric elongation of the hydrogen-oxygen bond.

 

This parametric elongation of the water molecule, according to the Stanley Meyer principle, is done by using High Voltage nano pulses at high frequency accross a cylindrical capacitor immersed in water.

 

The main particularity of the Stanley Meyer's WFC is that it uses the ordinary tap water without any add of electrolyt like a common electrolyser. Below some pages of the initial Stanley Meyer patent which shows the working principle of the Water Fuel Cell :

Stanley A Meyer Single Test Cell Voltrol
Stanley A Meyer Single Test Cell Voltrol

ere a video of the Stanley Meyer's (WFC) Water Fuel Cell in Action (close view) powered by the GEGENE with High Voltage, High Frequency nanopulses. The WFC is a water capacitor and uses ORDINARY TAP WATER without any electrolyte...

 TEST   S02E05 

We have observed in the previous test, that it is possible to use the GEGENE abovee as a pulsed current generator to power the Stanley Meyer's WFC. The previous test has showed that a great amount of stoechometric mixture is produced with a pure osmosed water without electrolyte but with too much current (10A). This strong current produced the heating of the water after few minutes. In this test, the induction cooker of the Gegene has been replaced by a double function generator (one modulating the other) and the flat bifilar coil by a cylindrical bifilar coil ( 2x1mH ) with a ferrite core.

Reproduced the VIC (Voltage Intensifier Circuit) signal of Stanley Meyer with the two function generators so as to get a parametrical excitation of the water molecule of the WFC and also to get a similar flow of gaz equivalent to the TESTS02E04.

Below the setup of the TEST-S02E05 :

The function genarator N°1 modulate the function generator N°2 and the signal is sent to the power amplifier with a Mosfet transistor IRFP450 and powered at 30 V DC.
The pulsed voltage is sent to WFC via an ultra fast diode HFA25PB60 and through the bifilar coil (L1,L2).

Two analog multimeters are used to measure the DC voltage and the DC current powering the amplifier.

Below The DC power supply confirms the DC voltage and current measured.

Below the signal measured accross the WFC.

The MAX voltage measured is 560 Volt and with this kind of pulsed current the amount of gaz is equivalent to the 1 KW of power sent by the GEGENE...

Comments : This test shows that it is possible to reduce dramatically the current spent (and thus the Joule losses) in the WFC by using a special pulsed signal...

Can we Tested the Gated PWM that Driver VIC?

TEST-S02E06 : Improvement of the parametric wave measured accross the WFC
The saison 2 of the Projet GEGENE (Great Efficiency GENErator)...
created on december 28, 2012 - JLN Labs - last update february 7, 2013
All informations and diagrams are published freely (freeware) and are intended for a private use and a non commercial use.


Toutes les informations et schémas sont publiés gratuitement ( freeware ) et sont destinés à un usage personnel et non commercial

Cliquez ici pour la version FRANCAISE 

 

February 6, 2013 - TESTS02E06 : This is the following of the TESTS02E05. The purpose of this test is to be the closest as possible to the parametric excitation wave which is able to broke the covalent bound of the water molecule as Stanley Meyer has discribed in his patent (see below) :

Stanley A Meyer Single Test Cell Voltrol

Here a test of the Stanley Meyer's Water Fuel Cell (WFC) with the VIC circuit v1.1. The WFC is filled with pure osmosed water without electrolyte The purpose of this test is to get the water molecule splitting by resonance with the stepping charge effect as described in the Stanley Meyer's patent.

The Voltage Intensifier Circuit (VIC) uses the same components from the previous test,

I have updated the previous diagram by adding a new ultra-fast switching diode (thanks to Milan Manchich for his suggestion).

And effectivly, in this new setup, the measured signal accross the WFC is very similar to the Stanley Meyer's patent.

Below the updated diagram of the WFC-VIC 1.1

Here the setup of the TEST-S02E06 :

he function genarator N°1 modulate the function generator N°2 and the signal is sent to the power amplifier with a Mosfet transistor IRFP450 and powered at 30 V DC.
The pulsed voltage is sent to WFC via the two ultra fast diodes HFA25PB60 and through the bifilar coil (L1,L2).

The resonance frequency has been tuned to 42.8 KHz modulated at 4.2 KHz with a DTC of 50%

Here the signal measured accross the WFC.

Comments : 

The new signal generated is more closer to the signal described in the Stanley Meyer's patent.

 

This new setup seems to improve significantly the splitting of the water molecule. It is important to notice that I have not observed the warming up of the water.

Support us on Patreon PLease Dan 

https://www.patreon.com/securesupplies

Stanley A Meyer Hydrogen
Stanley A Meyer Single Test Cell Voltrol
Stanley A Meyer Single Test Cell Voltrol
Stanley A Meyer Single Test Cell Voltrol

Special Note if  10 KHZ up you will get no bubbles

if Dc bounces to ac no bubbles

Andrija Puharich`s Circuit diagram

 •6 May 2017

Stanley and Stephen Meyer based some of their circuit thoughts on Andrija Puharich`s

and Nikola Tesla's circuit Works.

 

 

Andrija Puharich`s Patent US4394230A: https://www.google.com/patents/US4394230

 

Andrija Puharich`s Patent US3563246: https://www.google.com/patents/US3563246

 

Andrija Puharich`s Patent US3726762: https://www.google.com/patents/US3726762

My "Old" Circuit diagram: https://drive.google.com/open?id=0Bxn...

My "Improved" Circuit diagram: https://drive.google.com/open?id=0Bxn...

Andrija Puharich`s Wave Form: https://patentimages.storage.googleap...

Патент US4394230A,here

от мен на български език:

back up 

https://drive.google.com/open?id=0Bxn...

Andrija Puharich`s Blocking oscillator

Andrija Puharich`s Water Decomposition Waveform - Part 1

 

•29 Apr 2017

 

Andrija Puharich`s Blocking oscillator

Andrija Puharich`s Patent US4394230A: https://www.google.com/patents/US4394230

 

Патент US4394230A, преведен от мен на български език:

https://drive.google.com/open?id=0Bxn...

 

My Circuit diagram: https://drive.google.com/open?id=0Bxn...

 

Amplitude modulation - 3 frequencies is present:

https://drive.google.com/open?id=0Bxn...

 

Double Amplitude modulation - only 2 frequencies is present:

https://drive.google.com/open?id=0Bxn...

 

The Original Sound of Stanley Meyer`s Waveform:

https://www.youtube.com/watch?v=nbk5P...

 

(I publish this my "Sound analysis", 5 years ago. This Sound... is the same!!!)

 

Similar research forum`s link: http://www.ionizationx.com/index.php?...

 

Molecular Geometry of the Water molecule:

https://www.youtube.com/watch?v=DbCSa...

 

Nuclear Magnetic Spin Relaxation Time Constant of Water T1 = T2 = 2500 mS = 2,5 sec: http://hyperphysics.phy-astr.gsu.edu/...

 

Stephen Meyer`s "Frequency deviation", by changing Car Alternator`s RPM:

https://drive.google.com/open?id=0Bxn...

 

Another one Puharich`s calculation, at "dry cell" (not water added): "fc"

average = 62985 Hz, with ranges between 59748 Hz to 66221 Hz, 66221 Hz - 62985 Hz

= 3236 Hz (about +5,1%) 62985 Hz - 59748 Hz = 3237 Hz (about -5,1%)

 

Therefore, Carrier Resonant Sinusoidal signal = 62985 Hz, modulated with "Audio signal"

= 3236 Hz This wave form is shown in FIG.5:

https://drive.google.com/open?id=0Bxn...

Nuclear Spin and controlling Relaxation time

and magnetic effects on H2 and O

In NMR, a strong magnetic field is used to partially polarize the nuclear spins.

 

Taking protons as the most common example, the excess of proton spin in the direction of the magnetic field constitutes a small net magnetization of the material.

 

To set up the conditions for the observation of an NMR signal, strong radio frequency radiation is applied to the sample at the appropriate frequency to

produce "spin flips". From the quantum point of view, the RF photons

are absorbed by some of the protons to flip them from parallel to the magnetic

field to anti-parallel, a higher energy state.

When the exciting RF field is switched off, the protons tend to returned to their lower energy state. This "relaxation" back to a state where their spins are parallel to the static magnetic field produces a small amount of RF radiation which is detected as the NMR signal. Two different time constants for decay are typically observed.

The longer of the two time constants is usually labeled T1 and is associated with the decay of the field component that is parallel to the applied static magnetic field B0.

 

This field direction is usually taken to define the z-axis of the system.

 

This time constant is sometimes called the longitudinal time constant. It is also called the spin-lattice relaxation time.

Since the magnetic potential energy is proportional to the projection along this axis, a change in the magnetization along this axis involves the exchange of energy.

This implies that the spin has interacted with its environment.

For application to magnetic resonance imaging of the body, the interaction is a good thing because it implies the capacity to differentiate between different types of tissue.

The Original Sounds of Andrija Puharich`s and Stanley A Meyers

Basic Systems.  Remember there are over 11 Version all work.

This is VERSION 1 sound Recorded 16 Dec 2012

( sounds like a frog aree they releasing oxygen into the water ?)

Gods handy Work ?

 

Sound of Water Spliting

Frogs at Rest Sound, it is not a mating call

or call it is a at rest sound.

 

Sound of Water Spliting

Andrija Puharich`s Water Decomposition Waveform - Part 2

 

•29 Apr 2017

 

Andrija Puharich`s Blocking oscillator

Link to my previous video: https://www.youtube.com/watch?v=qQVtF...

 

Andrija Puharich`s Patent US4394230A: https://www.google.com/patents/US4394230

 

Патент US4394230A, преведен от мен на български език: https://drive.google.com/open?id=0Bxn...

 

My Circuit diagram: https://drive.google.com/open?id=0Bxn...

 

Amplitude modulation - 3 frequencies is present:

https://drive.google.com/open?id=0Bxn...

 

Double Amplitude modulation - only 2 frequencies is present: https://drive.google.com/open?id=0Bxn...

 

The Original Sound of Stanley Meyer`s Waveform: https://www.youtube.com/watch?v=nbk5P...

 

(I publish this my "Sound analysis", 5 years ago. This Sound... is the same!!!) Similar research forum`s link: http://www.ionizationx.com/index.php?...

 

Molecular Geometry of the Water molecule:

https://www.youtube.com/watch?v=DbCSa...

 

Nuclear Magnetic Spin Relaxation Time Constant of Water T1 = T2 = 2500 mS = 2,5 sec: http://hyperphysics.phy-astr.gsu.edu/...

 

Stephen Meyer`s "Frequency deviation", by changing Car Alternator`s RPM: https://drive.google.com/open?id=0Bxn...

 

Another one Puharich`s calculation, at "dry cell" (not water added):

"fc" average = 62985 Hz, with ranges

between 59748 Hz to 66221 Hz, 66221 Hz - 62985 Hz = 3236 Hz

(about +5,1%) 62985 Hz - 59748 Hz = 3237 Hz (about -5,1%)

Therefore, Carrier Resonant Sinusoidal signal = 62985 Hz,

modulated with "Audio signal" = 3236 Hz

 

This wave form is shown in FIG.5: https://drive.google.com/open?id=0Bxn...